Victron Energy Smart BatteryProtect 48V 100A – BPR110048000 - Camper-Camper
Shopping Cart

No products in the basket.

Shopping Cart

No products in the basket.

Victron Energy Smart BatteryProtect 48V 100A – BPR110048000

£167.04

SKU:BPR110048000 Categories,

The Smart BatteryProtect 48V 100A disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.

When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin.

If required, Bluetooth can be disabled.

The Smart BatteryProtect 48V 100A is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the IN terminal to the OUT terminal. In case of use with a load, the battery connects to the IN terminal, and in case of use with a charger, the charger connects to the IN terminal.

 

Features of the Battery Protect 48V 100A

Protects the battery against excessive discharge and can be used as a system on/off switch
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
The on/off input can be used as a system on/off switch.

 

Bluetooth: programming made easy
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.
Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin.
If required, Bluetooth can be disabled.

 

Over voltage protection
To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3V respectively 32.6V.

 

Ignition proof
No relays but MOSFET switches, and therefore no sparks.

 

Delayed alarm output
The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds.
Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

 

A special setting for Li-ion batteries
In this mode the Smart BatteryProtect 48V 100A can be controlled by the VE.Bus BMS.

 

Ultra-low current consumption
This is important in case of Li-ion batteries, especially after low voltage shutdown.

 

Delayed load disconnect and delayed reconnect
The load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected.
The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

 

Monitor, operate & control your system

Use the VictronConnect app to configure, monitor, update and diagnose your Smart BatteryProtect. It can connect to Victron products via Bluetooth, USB and WiFi/LAN/Internet.

See the VictronConnect product page for more information.

Additional information

Brand

Victron Energy

Manufacturer Part Number

BPR110048000

GTIN

8.72E+12

Voltage

48V

Max. Continuous Load Current

100A

Peak Current (During 30 Seconds)

250A

Operating Voltage Range

24 – 70 V

Alarm Output Delay

12 seconds

Max. Load on Alarm Output

50mA

Load Disconnect Delay

90 seconds

Protection Category

Electronics: IP67 (potted), Connections: IP00

Connection

M8

Mounting Torque

9 Nm

Bluetooth Enabled

Yes

Dimensions

H62 x W123 x D120mm

Weight

0.8Kg

Warranty

5 Years

Country of Manufacture

India